Decra led self adhesive strips were great for this faux stained glass door panel
but what to do with the left overs?
I jave been upcycling glass bottles and jars aplenty. in this case a simple coffee jar with a good seal in the lid
looks great with the panels painted with left over glass paint but not for food containers as it warps ones expectations of the contents. Blue sugar anyone? Painted glass best for Epsom salts or potpourri storage.
particularly good for up cycling (white) wine bottles to hold our home made vinegars, sorry I gave them away before I remembered to photograph them.
so to use up the rest of the packs I am off to the charity shop tomorrow to titivate a couple of vases.
a simple way to organize the sack of ribbon scraps…
materials: 1 A4 sheet cardstock (I used craft card), scissors, strong tape or glue, hole punch Washi tape to close and decorate
score and fold card into toblerone shape – I scored at 6.5, 13 and 19cm then turned the card and scored at 4 cm from either side
i then cut up the 4cm score lines, trimmed and wedged the flaps created to make triangles as shown
I then hole punched 14 holes (enough to squeeze in different scraps of ribbons, if it will wrap round an A6 card, I keep it). I only have an office ring binder punch so was limited to punch near a score line but the holes can be wherever you want). Then form the toblerone shape and stick the overlapping triangles together. I used red liner tape.
Poke ends of ribbon through the holes from inside to out, a crochet hook works well, and when your holder is full secure it closed with washi tape so you can top it up some time in the future without destroying the box
just a few more to make before I get the ribbon stash under control!
if decorated this would make a nice little gift for a crafty friend…
Take one pair of jeans and too many hours on Pinterest and let us see what we can make….
so far the bottom of the legs have been chopped off and made into two simple storage pots.
I boxed the bottoms (the tops really to preserve the hems) and lined with some dotty fabric and some wadding. One leg had a longer lining piece to create a bigger contrast cuff
These will be used to store ready readers and sunglasses.
If I made them again and had enough firm form interface I would use that to make the sides more rigid but these will do the soft storage job
Now back to Pinterest to see what else to try … I have ppreviously made a garden apron/belt, some oven gloves and mitts -see earlier posts- so want to expand my jeans recycling repertoire
Oh dear, I was Trying to use up supplies as the cupboards are full, but a sale in paperchase undid my efforts
bAck homeI made two quick cards, just lining up the range of tapes direct on to cream linen effect card bases.
For the first I stamped in the gap, taking care to line it up.l I then realized if I put the greeting on first I could easily line the tape along it so for the second I stuck on a greeting (my handwriting scanned into scan n cut, cut three times on card and layered to create dimension) before taping around it
in both cases the tape is glamorous enough (Paperchase peacock collection, only four pounds for 8 rolls) to leave off embellishment but some gems on one and black stickles on the other just finished it if
now back to my resolution about not adding to the craft hoard!
I wanted to present some of my mountain of hand made cards so I made gift bags using a roll of wallpaper (I buy 50p remnant rolls of the more ornate papers when I see them). This is sturdier and more pliable than paper or card.
method: cut a rectangle of paper about 34cm wide by 20 high ie just bigger than A4, this will hold 8 ish A6 cards and envelopes
fold about 3 cm down and towards you to make a cuff with the reverse of the paper showing, then score down over the cuff at 3 cm, 16 cm, 19 cm, 32 cm – all the way to the bottom
then fold under about all the way across about 3 cm from the bottom to make your base
cut up the score lines from the bottom to that last across score line to make the bottom flaps and cut out the tiny rectangle bottom right
fold the score lines to form the bag shape
stick double sided tape on the right hand down strip and bottom flaps to fix bag
punch matching pairs of holes in the cuff front and back, I used an office hole punch which fit inside the bag neatly. Thread ribbon or cord through the holes and tie knots inside the bag to fasten
if needed cut a piece of card to fit inside the bottom to reinforce the base, wallpaper seems strong enough for a light package though
You can pinch the side panels to give the impression of a side gusset and embellish or label as well..
I followed a scan n cut you tube idea to create some home made decor this year. A modern version of paper chains!
For a Christmas themed garland you will need to cut out an assortment of paper snowflakes in different sizes. I used a selection of papers and wish I had chosen doubled sided stuff as the garland twists a little in use.
if you don’t have a cutting machine folding the paper and hand cutting is an option if you have the time (or child labour!)
at the sewing machine pull a long tail of thread through then sew a long straight stitch through the centre of the first flake. (I used a white thread as most of the papers were pale or had white in but a contrast thread in a decorative stitch might be fun).
Be brave, go straight off the end of the flake and sew a few stitches in the gap before you put the next snowflake through. This creates a chain for your garland. You can overlap a few flakes or stitch a small one on top of a larger one as well.
Continue for the length you wish and leave a long tail of thread at the end for tying.
Easy to recreate for Valentines, Spring, Easter, Birthday, Halloween or Anniversary versions …
Tip: remember that paper will blunt your machine needle
Scraps of card were cut into label shapes with the scan n cut then decorated with die cuts from the enormous , seemingly endless, Natures Gallery Docrafts bundle. I stamped ‘to’ and ‘from’ and tied twine in place then made a mini folder pocket to hold them in.
I then got in the mood with old Christmas cards cut the same way and a shaker card version too. This required a bit of organization to put the same weight of card through the scan n cut at the same pass but really effective.